CROWN CRUISER 26
26' MODEL SHOWN

WILL ACCOMMODATE INBOARD MOTORS, SINGLE OR

DUAL OUTBOARD MOTORS OR STERN DRIVE UNITS

Photo on the left was sent to us all the way from Malta (Europe) by a very proud customer who writes, "This is truly the finest boat in the Mediterranean, thanks to your Boat Kit." You too can be a proud owner of a Crown Cruiser. Built from our Plans and Patterns, Frame Kit or complete Boat Kit ... Anyway you choose, you can be sure of owning one of the best designed, finest performing cruisers afloat.

Move up to the luxury cruiser you've been waiting for. Note the graceful lines of the Crown Cruiser giving the heavily flared section forward that is turn gives this design its exceptional form and appearance. A big, roomy boat featuring trend setting styling plus the most usable cabin arrangement possible. Cabin is divided with bunk area forward and galley and head in the aft section of the cabin. Spacious after deck is ideal for entertaining.

The galley is a full 36" wide and 26" deep. Adequate room for stove and sink with fresh water tanks in toilet enclosure or in storage locker.The room under the galley is adequate for dishes, ice chest, silverware, and for the storage of food. Over 15 cubic feet of storage srea available.

Fully enclosed private toilet room. A full 6' high and measures 2' X 3', all parts included except the toilet itself which is an accessory. The toilet doors are on a sliding track (so when they are open they do not block the passageway.)

All windshields and side windows are made of clear 3/16" plexiglass. Both side windows are on sliding tracks that open for ventalation.

The aft cabin floor measures 18" from the top of the floor to the bottom of the keel. Larger inboard engines would be able to be installed partially below the floor line - only a small motor cover would then be necessary which can be used as a center seat. This boat is recommended for stern drive units or inboard engine installation, however larger horsepower outboard motors can be used, with, or without, a transom extension kit.

The forward compartment is a large spacious srea for anchor, rope, life-preservers and other miscellaneous gear. If extra length bunks are desired, this forward bulkhead can be left out, greatly increasing the length of both bunks.

COMPLETE BOAT KIT. You get everything you need to build this spacious Crown Cruiser. All parts are pre cut from solid mahogany and marine plywood. Assembly is fool proof. Easy to follow, step by step instructions are included.

For high horsepower engines, a double 1/4" bottom is available and recommended, along with the Epoxy Plus fiberglass covering kit.

WHAT DOES ONE OF OUR SATISFIED CUSTOMERS
HAVE TO SAY ABOUT THIS BOAT?


Step by Step Instructions - Step by step instructions for our boat kits have been designed for those who have never built a boat before. As you can see in drawing at left and right, each part in the hull is assigned a number, this number in turn is imprinted on each piece of mahogany and marine plywood that is included in the complete boat kit, Using this technique an amateur can easily assemble any kit listed on this site.
POWERBOAT - CROWN CRUISER 26
LENGTH 26'
BEAM8'
DRAFT12"
FREEBOARD AFT34"
COCKPIT6' 8" X 11'
CABIN 6' 6" X 12'
BERTHS6'
SLEEPS4
HEAD ROOM6'
BOTTOM PLANKING3/8" PLYWOOD
SIDE PLANKING3/8" PLYWOOD
FRAMES7/8" SOLID MAHOGANY
WEIGHT2000 LBS.
POWER100 TO 250
SPEED20 - 35 MPH
CONSTRUCTIONCONVENTIONAL
WHAT IS CONVENTIONAL CONSTRUCTION?

WHAT IS A BRONZE FASTENING KIT ?

WHAT IS AN EPOXY-PLUS COVERING KIT ?

Design Number: # PB 72X
ItemsQuantityUnit Price
Plans and Patterns:[146]
Frame Kit:[2275]
Hull Kit:[5680]
Boat Kit:[12825]
Bronze Fastening Kit:[797]
Epoxy Plus Kit:[844]